HDLP-S500のハードウェア情報

前の記事で「HDLP-S500にSSHで接続する」を書いたが、この記事でssh接続で確認できたハードウェア情報をベロベロはることにする。

I-O DATA LAN&USB接続ハードディスク LAN DISK 500GB HDLP-S500

いくつかの値をベロベロ書く。追加確認希望があればコメントをして欲しい。

uname -a

Linux nas01 2.6.15 #1 Tue Jan 11 21:33:48 JST 2011 armv4l GNU/Linux

結構古いカーネルを使っている。CPUはARMを使っているようだ。詳細は次。

/etc/debian_version

4.0

Debian 4.0とはいと古うございますな。

/proc/cpuinfo

Processor : FA526id(wb) rev 1 (v4l)
BogoMIPS : 230.19
Features : swp half
CPU implementer : 0x66
CPU architecture: 4
CPU variant : 0x0
CPU part : 0x526
CPU revision : 1
Cache type : write-back
Cache clean : cp15 c7 ops
Cache lockdown : format B
Cache format : Harvard
I size : 16384
I assoc : 2
I line length : 16
I sets : 512
D size : 8192
D assoc : 2
D line length : 16
D sets : 256

Hardware : GeminiA
Revision : 0000
Serial : 0000000000000000

クロックは400MHzとのこと。

/proc/meminfo

MemTotal: 60828 kB
MemFree: 2828 kB
Buffers: 92 kB
Cached: 2280 kB
SwapCached: 4376 kB
Active: 39872 kB
Inactive: 3104 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 60828 kB
LowFree: 2828 kB
SwapTotal: 2120572 kB
SwapFree: 1925100 kB
Dirty: 0 kB
Writeback: 0 kB
Mapped: 42316 kB
Slab: 10220 kB
CommitLimit: 2150984 kB
Committed_AS: 311656 kB
PageTables: 1436 kB
VmallocTotal: 188416 kB
VmallocUsed: 1584 kB
VmallocChunk: 186348 kB

潤沢とは思っていなかったが、まさか64MBとは思っていなかった。起動直後からスワップアウトしている。(sshdを起動して接続しているせいかもしれない。)

dmesg

Linux version 2.6.15 (kodaka@devsrv) (gcc version 3.4.4 20041218 (prerelease) (Debian 3.4.3-1)) #1 Tue Jan 11 21:33:48 JST 2011
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: GeminiA
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
DMA zone: 16384 pages, LIFO batch:3
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
Built 1 zonelists
Kernel command line: root=/dev/hdb2 ro mem=64M console=ttySL0,115200 initrd=0x00800000,16M
PID hash table entries: 512 (order: 9, 8192 bytes)
Bus: 150MHz(2/1)
Console: colour dummy device 80x30
sl2312 console setup :
Disable IDE...config to SATA mode
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 44288KB available (2737K code, 1233K data, 96K init)
Calibrating delay loop... 230.19 BogoMIPS (lpj=1150976)
Mount-cache hash table entries: 512

Page_chain_cachep Init!***

CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 16384K
NET: Registered protocol family 16
PCI: bus0: Fast back to back transfers disabled
sl2312_pci_map_irq : slot = 0 pin = 1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.25 [Flags: R/O].
fuse init (API version 7.3)
SGI XFS with large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered
Real Time Clock Driver v0.10
Gemini Gpio init
Register Gemini Power control
Watchdog Timer Initialized
Storm crypto Initialization
ttySL0 at MMIO 0x42000000 (irq = 18) is a SL2312
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
ipddp.c:v0.01 8/28/97 Bradford W. Johnson
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson
VSC-switch not found
Storm Semiconductors,Inc. SL351x Giga Ethernet driver 0.1.7 built at Jan 11 2011 21:31:46
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide 1: physical = 63400000, virtual = c4800000, irq = 5
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
MASTER not exist
hdb: TOSHIBA MK5059GSXP, ATA DISK drive
hdb speed:U5 (50MHz)(0x45)
ide0 at 0xc4800020-0xc4800027,0xc4800036 on irq 5
hdb: max request size: 1024KiB
hdb: 976773168 sectors (500107 MB) w/8192KiB Cache, CHS=60801/255/63
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
hdlp_partition: found hidden partition table.
hdb1 hdb2 hdb3 hdb4 hdb5
hdb1
hdlp_partition: found MBR partition table.
hdb6
libata version 1.20 loaded.
SL2312 MTD Driver Init.......
sl2312flash_init: value=0x82c22035
sl2312flash_init: value=0x82c22025 after mask
SL2312 CFI Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
SL2312 CFI Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 2 MTD partitions on "SL2312 CFI Flash":
0x00000000-0x00070000 : "SL boot"
0x00070000-0x00080000 : "VCTL"
SL2312 MTD Driver Init Success ......
FTC_FOTG2XX : Init FOTG2XX Driver
Init FOTG2xx driver
FTC_FOTG2XX : >>> Found FOTG2XX ...
pFTC_OTG c16182a0
hcd->self.controller c16aac00
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX ehci-hcd-FOTG2XX: new USB bus registered, assigned bus number 1
usb_register_bus
ghcd_FOTG2XX hcd c16aac00
hcd_irq_For_OTG
ehci->caps->length 10, hcd->regs f6800000 , ehci->regs f6800010
udev->state 1
drivers/usb/host/ehci-hcd-FOTG2XX.c: USB support enabled, EHCI rev 101. 0
Timing on EOF1(0xf6800040) = 0xd
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FTC_FOTG2XX : >>> +FOTG2XX_get_otg_transceiver
FTC_FOTG2XX : registered host c16aac00
OTG2XX act as HOST only (don't need to wait gadget driver)

1. (OTGC_Init)

pFTC_OTG->otg.default_a=1

1. (OTGC_Init)

pFTC_OTG->otg.default_a=1
OTG_enable_VBUS
FTC_FOTG2XX : >>> Drive VBUS ok...

1. OTGP_Close()

OTG2XX act as HOST only (remove gadget function)

1. OTGH_Open()(0x30=0x0)

OTG_enable_VBUS
mdwOTGC_Control_A_VBUS_VLD_Rd 80000

1. OTGP_Close()

OTG2XX act as HOST only (remove gadget function)

1. OTGH_Open()(0x30=0x0)

ehci otg_set_host status 0
connect_change 1
clear_bit
mice: PS/2 mouse device common for all mice
ipsec_init : cryptographic accelerator
ipsec tx_desc = ffc10000
ipsec rx_desc = ffc11000
ipsec tx_desc_dma = 016d3000
ipsec rx_desc_dma = 016d4000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 5
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: deregistering driver usb-storage
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing init memory: 96K
Adding 2120572k swap on /dev/hdb3. Priority:-1 extents:1 across:2120572k
EXT3 FS on hdb2, internal journal
ufsd_lbd: module license 'Commercial product' taints kernel.
ufsd: driver loaded at bf000000 built on Aug 12 2010 02:30:13
UFSD version 7.02h (Aug 12 2010, 02:15:10)
NTFS read/write support included
$Id: ufsdvfs.c,v 1.204.2.2 2010/08/11 17:05:21 shura Exp $ (LBD=ON)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
GMAC-0 Addr 1 Vendor ID: 0x001cc912
mii_write: phy_addr=0x1 reg_addr=0x4 value=0x5e1
mii_write: phy_addr=0x1 reg_addr=0x9 value=0x300
mii_write: phy_addr=0x1 reg_addr=0x18 value=0x41
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x9200
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x1200
Link Up (0x796d) MII REG 10 = 0x3800
1000M/Full
Flow Control Enable.
Storlink eth0 address = ************
Enable MAC Flow Control...
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
EXT3 FS on hdb2, internal journal
oom-killer: gfp_mask=0x200d2, order=0
Mem-info:
DMA per-cpu:
cpu 0 hot: low 0, high 18, batch 3 used:0
cpu 0 cold: low 0, high 6, batch 1 used:5
DMA32 per-cpu: empty
Normal per-cpu: empty
HighMem per-cpu: empty
Free pages: 2092kB (0kB HighMem)
Active:39 inactive:10499 dirty:0 writeback:0 unstable:0 free:523 slab:2545 mapped:10526 pagetables:331
DMA free:2092kB min:2048kB low:2560kB high:3072kB active:156kB inactive:41996kB present:65536kB pages_scanned:19693 all_unreclaimable? no
lowmem_reserve: 0 0 0 0
DMA32 free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve: 0 0 0 0
Normal free:0kB min:0kB low:0kB high:0kB active:0kB inactive:0kB present:0kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve: 0 0 0 0
HighMem free:0kB min:128kB low:128kB high:128kB active:0kB inactive:0kB present:0kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve: 0 0 0 0
DMA: 11*4kB 54*8kB 3*16kB 1*32kB 0*64kB 0*128kB 0*256kB 1*512kB 1*1024kB 0*2048kB 0*4096kB = 2092kB
DMA32: empty
Normal: empty
HighMem: empty
Swap cache: add 88770, delete 87515, find 20722/30192, race 0+0
Free swap = 1994612kB
Total swap = 2120572kB
Free swap: 1994612kB
16384 pages of RAM
727 free pages
1195 reserved pages
2545 slab pages
1432 pages shared
1255 pages swap cached
Out of Memory: Killed process 1315 (apache2).

USBストレージはバックアップ用かと思われるが、sshから操作すればバックアップ以外にもストレージの保存用に拡張できるのかな。

df

Filesystem 1K-ブロック 使用 使用可 使用% マウント位置
rootfs 379391 227233 148303 61% /
/dev/root 379391 227233 148303 61% /
tmpfs 30412 548 29864 2% /mnt/tmpfs
tmpfs 30412 0 30412 0% /lib/init/rw
tmpfs 30412 0 30412 0% /dev/shm
/dev/hdb1 316232 151596 161424 49% /boot
/dev/hdb5 3263443 42758 3056822 2% /mnt/hda5
/dev/hdb6 482142776 115620128 366522648 24% /mnt/hda6

mount

rootfs on / type rootfs (rw)
/dev/root on / type ext3 (ro,noatime,data=ordered)
tmpfs on /mnt/tmpfs type tmpfs (rw)
tmpfs on /lib/init/rw type tmpfs (rw,nosuid)
proc on /proc type proc (rw,nodiratime,nosuid,nodev,noexec)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec)
usbfs on /proc/bus/usb type usbfs (rw,nosuid,nodev,noexec)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
devpts on /dev/pts type devpts (rw,nosuid,noexec)
/dev/hdb1 on /boot type ext3 (ro,noatime,data=ordered)
/dev/hdb5 on /mnt/hda5 type ext3 (rw,data=ordered)
/dev/hdb6 on /mnt/hda6 type ufsd (rw,nodiratime)

/etc/

HDLFind.conf group mailcap resolv.conf
HDLFind_port65.conf group- mailcap.order resolvconf
Net gshadow mailname rmt
X11 gshadow- mime.types rpc
adduser.conf hdparm.conf mke2fs.conf samba
adjtime host.conf modprobe.d securetty
aliases hostname modules security
alternatives hosts motd services
apache2 hosts.allow motd.tail sgml
apm hosts.deny mt-daapd shadow
apt hotplug mtab shadow-
avahi hotplug.d netatalk shells
bash.bashrc inetd.conf network skel
bash_completion init.d networks slp.conf
bash_completion.d inittab nsswitch.conf slp.reg
blkid.tab inputrc opt slp.spi
blkid.tab.old issue pam.conf smartd.conf
calendar issue.net pam.d smartmontools
cron.d issue.orig passwd smbldap-tools
cron.daily jcpd.conf passwd- ssh
cron.hourly ld.so.cache perl ssl
cron.monthly ld.so.conf php5 sysctl.conf
cron.weekly ld.so.conf.d printcap terminfo
crontab ldap profile timezone
cups lld2d.conf protocols ucf.conf
dbus-1 locale.gen rc.local udev
debconf.conf localtime rc0.d udhcpc.cache
debian_version logcheck rc1.d updatedb.conf
default login.defs rc2.d vim
deluser.conf logrotate.conf rc3.d wgetrc
dhclient logrotate.d rc4.d xml
dhcp3 logrotate_post rc5.d
dpkg lsb-base rc6.d
fstab magic rcS.d

ps aux

USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 1 0.0 0.1 1896 92 ? S Sep04 0:04 init [2]
root 2 0.0 0.0 0 0 ? SN Sep04 0:00 [ksoftirqd/0]
root 3 0.0 0.0 0 0 ? S< Sep04 0:00 [events/0]
root 4 0.0 0.0 0 0 ? S< Sep04 0:00 [khelper]
root 5 0.0 0.0 0 0 ? S< Sep04 0:00 [kthread]
root 13 0.0 0.0 0 0 ? S< Sep04 0:00 [kblockd/0]
root 16 0.0 0.0 0 0 ? S< Sep04 0:00 [khubd]
root 44 0.1 0.0 0 0 ? S Sep04 0:11 [pdflush]
root 45 0.1 0.0 0 0 ? S Sep04 0:10 [pdflush]
root 47 0.0 0.0 0 0 ? S< Sep04 0:00 [aio/0]
root 46 0.2 0.0 0 0 ? D Sep04 0:19 [kswapd0]
root 49 0.0 0.0 0 0 ? S< Sep04 0:00 [xfslogd/0]
root 50 0.0 0.0 0 0 ? S< Sep04 0:00 [xfsdatad/0]
root 51 0.0 0.0 0 0 ? S< Sep04 0:04 [xfsbufd]
root 675 0.0 0.0 0 0 ? S< Sep04 0:00 [ata/0]
root 677 0.0 0.0 0 0 ? S Sep04 0:00 [mtdblockd]
root 741 0.0 0.0 0 0 ? S Sep04 0:00 [kjournald]
root 965 0.0 0.0 0 0 ? S Sep04 0:00 [kjournald]
root 966 0.0 0.0 0 0 ? S Sep04 0:00 [kjournald]
root 1079 0.0 0.0 0 0 ? S Sep04 0:00 [eth0]
root 1120 0.0 0.0 1704 32 ? Ss Sep04 0:00 /usr/local/udhcpc/udhcpc -a -r 192.168.*.* -p /var/run/udhcpc.et
100 1229 0.0 0.1 2504 80 ? Ss Sep04 0:00 /usr/bin/dbus-daemon --system
avahi 1241 0.0 0.1 3064 108 ? S Sep04 0:00 avahi-daemon: running [nas01.local]
avahi 1242 0.0 0.1 3064 64 ? Ss Sep04 0:00 avahi-daemon: chroot helper
daemon 1250 0.0 0.1 1916 116 ? Ss Sep04 0:00 /usr/sbin/slpd
root 1256 0.0 0.0 5148 60 ? Ss Sep04 0:00 /usr/sbin/sshd
root 1259 0.0 0.0 884 4 ? Ss Sep04 0:00 syslogd -m 0 -s 49
root 1276 0.0 0.2 1532 144 ? S Sep04 0:00 /opt/microsoft/lldp/lld2d -d eth0
root 1283 0.0 0.1 1924 72 ? S Sep04 0:00 /usr/local/bin/jcpd -f /etc/jcpd.conf
root 1289 0.0 0.3 2272 200 ? Ss Sep04 0:00 /usr/sbin/cron
root 1301 0.0 0.2 18812 168 ? Ss Sep04 0:00 /usr/sbin/apache2 -k start
www-data 1311 0.0 0.1 19208 96 ? S Sep04 0:02 /usr/sbin/apache2 -k start
www-data 1312 0.0 0.1 19616 108 ? S Sep04 0:03 /usr/sbin/apache2 -k start
www-data 1314 0.0 0.1 18948 92 ? S Sep04 0:06 /usr/sbin/apache2 -k start
www-data 1316 0.0 0.1 18948 104 ? S Sep04 0:04 /usr/sbin/apache2 -k start
root 1318 0.0 0.0 1672 36 ? S Sep04 0:00 /usr/local/bin/HDLFind
root 1323 0.0 0.0 1672 36 ? S Sep04 0:00 /usr/local/bin/HDLFind_port65
root 1337 0.0 0.3 1516 192 ? S Sep04 0:00 /usr/local/bin/usbhdmng
root 1537 0.3 0.1 7844 116 ? S Sep04 0:26 /usr/sbin/afpd -U uams_dhx2.so,uams_dhx.so,uams_clrtxt.so,uams_ra
root 1540 0.0 0.1 2208 84 ? S Sep04 0:00 /usr/sbin/cnid_metad
root 1553 0.0 0.9 20600 600 ? Ss Sep04 0:00 ./dms_sync conf /mnt/hda5/dms
root 1555 0.0 0.9 20600 600 ? S Sep04 0:00 ./dms_sync conf /mnt/hda5/dms
root 1558 0.0 0.9 20600 600 ? S Sep04 0:02 ./dms_sync conf /mnt/hda5/dms
root 1559 0.0 0.9 20600 600 ? RN Sep04 0:03 ./dms_sync conf /mnt/hda5/dms
root 1560 0.0 0.9 20600 600 ? RN Sep04 0:00 ./dms_sync conf /mnt/hda5/dms
root 1561 0.0 0.9 20600 600 ? S Sep04 0:00 ./dms_sync conf /mnt/hda5/dms
root 1568 0.0 0.3 11884 188 ? S Sep04 0:00 /usr/sbin/mt-daapd -c /etc/mt-daapd/mt-daapd.conf
root 1569 0.0 0.3 13928 184 ? S Sep04 0:00 /usr/sbin/mt-daapd -c /etc/mt-daapd/mt-daapd.conf
root 1571 0.0 0.3 13928 184 ? S Sep04 0:00 /usr/sbin/mt-daapd -c /etc/mt-daapd/mt-daapd.conf
root 1577 0.0 0.3 13928 184 ? S Sep04 0:00 /usr/sbin/mt-daapd -c /etc/mt-daapd/mt-daapd.conf
root 1600 0.0 0.9 6524 568 ? Ss Sep04 0:00 /usr/sbin/nmbd -D
root 1602 0.0 0.1 9940 80 ? Ss Sep04 0:00 /usr/sbin/smbd -D
root 1607 0.0 0.1 9940 68 ? S Sep04 0:00 /usr/sbin/smbd -D
root 1622 0.0 0.0 1372 20 ? Ss Sep04 0:00 /usr/local/bin/btdog /usr/local/bin/bt -daemon-loop
root 1623 2.1 60.2 240304 36652 ? R Sep04 2:18 /usr/local/bin/bt -daemon-loop
root 1636 0.0 60.2 240304 36652 ? S Sep04 0:00 /usr/local/bin/bt -daemon-loop
root 1637 10.6 60.2 240304 36652 ? R Sep04 11:30 /usr/local/bin/bt -daemon-loop
root 1641 57.8 60.2 240304 36652 ? R Sep04 62:36 /usr/local/bin/bt -daemon-loop
root 1642 21.3 60.2 240304 36652 ? S Sep04 23:07 /usr/local/bin/bt -daemon-loop
root 1646 0.0 60.2 240304 36652 ? S Sep04 0:00 /usr/local/bin/bt -daemon-loop
www-data 1659 0.0 0.1 19592 96 ? S Sep04 0:00 /usr/sbin/apache2 -k start
root 1664 0.0 0.0 1444 48 ttySL0 Ss+ Sep04 0:00 /sbin/getty -L ttySL0 115200 vt102
root 1666 0.0 0.1 7844 116 ? S Sep04 0:00 /usr/sbin/afpd -U uams_dhx2.so,uams_dhx.so,uams_clrtxt.so,uams_ra
root 1667 0.0 0.1 7844 116 ? S Sep04 0:00 /usr/sbin/afpd -U uams_dhx2.so,uams_dhx.so,uams_clrtxt.so,uams_ra
www-data 1669 0.1 0.1 19628 108 ? S Sep04 0:07 /usr/sbin/apache2 -k start
www-data 1718 0.0 0.1 18948 108 ? S Sep04 0:02 /usr/sbin/apache2 -k start
www-data 1719 0.0 0.1 19700 108 ? S Sep04 0:02 /usr/sbin/apache2 -k start
www-data 1720 0.0 0.1 18948 104 ? S Sep04 0:05 /usr/sbin/apache2 -k start
root 1745 0.0 0.6 8380 400 ? Ss Sep04 0:04 sshd: root@pts/0
root 1759 0.0 1.4 4720 880 pts/0 Ss Sep04 0:00 -bash
www-data 1879 0.0 0.1 18948 92 ? S 00:34 0:00 /usr/sbin/apache2 -k start
root 1940 17.0 1.6 4160 976 pts/0 R+ 01:11 0:00 ps aux

管理パネルはApacheを利用して直に提供している様子。

おまけ

perl --version

This is perl, v5.8.8 built for arm-linux-gnu-thread-multi

Copyright 1987-2006, Larry Wall

php --version

PHP 5.2.0-8+etch7+L1 (cli) (built: Jan 10 2012 21:06:51)
Copyright (c) 1997-2006 The PHP Group
Zend Engine v2.2.0, Copyright (c) 1998-2006 Zend Technologies

以上で、大体わかったと思う。とりあえず、CPUはそんなに速くなく、メモリは逼迫している。ディストリビューションはおよそDebian 4.0を採用している。Perlはまだしも、PHPも入っているなどあまりカスタマイズされていない。その証拠にXもインストールされている。

玄箱なんかをLinuxボックス化しなくても、これは素のままで結構使えそう。とりあえずPerlでスクリプトを書いてぶん回しておけば、ダウンローダなんかにも出来る。低消費電力なので常時回して置けるし、HDDも500GBと申し分ない。

「apt-get」コマンドもそのまま入っていたが、怖くて実行していない。さすがにこれは止められているだろうか・・。

I-O DATA LAN&USB接続ハードディスク LAN DISK 500GB HDLP-S500

I-O DATA LAN&USB対応HDD LAN DISK Home HDLP-Sシリーズ 1.0TBモデル HDLP-S1.0

玄人志向 NAS 組み立てキット 玄箱シリーズ KURO-BOX